Skip to content

Home Dispensing products

Dispensing products

Dispense controllers

Control for consistent dots, beads and fills. LinkTech configures time-pressure and valve controllers for bench stations, fixtures and automated equipment.

SET / San-Ei Tech SDP420

Product range

Equipment for your application

Explore the models and configurations below. Our engineers can help with equipment selection, application testing and integration.

SET / San-Ei Tech SDP420

SET / San-Ei Tech

SDP420 Dispensing Controller

Compact digital controller for timed dispensing of adhesives, lubricants and assembly fluids. Vacuum adjustment and a teach function help set up each dispensing cycle.

Sizes & technical details
ItemDetails
Dispensing modesTimed, steady and teach
Dispensing time0.005–999.9 s
Pressure setting0–0.50 MPa
Vacuum setting0 to −20 kPa

Enquire about this product ↗

SET / San-Ei Tech SDP520

SET / San-Ei Tech

SDP520 Dispensing Controller

Digital dispensing controller for operator stations and automated equipment. Set dispensing conditions on the display and connect the completion signal to the next process step.

Sizes & technical details
ItemDetails
Dispensing modesTimed, steady and teach
Dispensing time0.005–999.9 s
Pressure setting0–0.60 MPa
External interfaceD-sub 9-pin I/O

Enquire about this product ↗

SET / San-Ei Tech SVC720V

SET / San-Ei Tech

SVC720V Valve Controller

Programmed valve control with built-in regulation of syringe or material-tank pressure. Suitable for integrating a dispensing valve into a manual station or an automated sequence.

Sizes & technical details
ItemDetails
Dispensing time0.005–999.9 s
Air input0.4–0.7 MPa
Pressure regulationBuilt-in syringe/tank regulator
Trigger inputFoot pedal or external I/O

Enquire about this product ↗

SET / San-Ei Tech SVC620S

SET / San-Ei Tech

SVC620S Spray Valve Controller

Digital controller for spray-valve timing and atomizing air. Air delays before and after spraying provide control over the start and finish of each coating pass.

Sizes & technical details
ItemDetails
Atomizing air0–0.50 MPa
Dispensing time0.005–999.9 s
Air timingPre-spray and post-spray delays
Trigger inputFoot pedal or external I/O

Enquire about this product ↗

SET / San-Ei Tech SVC620CD

SET / San-Ei Tech

SVC620CD Coating Valve Controller

Dedicated controller for the SV91CD coating valve. Switch between dot, line and spray application through I/O to suit the programmed coating process.

Sizes & technical details
ItemDetails
Compatible valveSV91CD
Application modesDot, line and spray
Mode selectionExternal I/O
InstallationLow-profile enclosure

Enquire about this product ↗

SET / San-Ei Tech SVC720F

SET / San-Ei Tech

SVC720F Conformal Coating Controller

Controller for conformal-coating valves, designed to drive a solenoid mounted close to the valve. Its low-profile enclosure supports installation within coating equipment.

Sizes & technical details
ItemDetails
ApplicationConformal coating
Dispensing time0.005–999.9 s
Supply24 V DC
External interfaceD-sub 9-pin I/O

Enquire about this product ↗

controller sk1 1 front

SK1-1

Touchscreen controller for one mono dispensing valve, with switching-signal control.

Sizes & technical details
ItemDetails
Dimensions as printed250(W) × 220(D) × 125(H)
Weight3.4 kg
Power supplyAC 110–250 V, 50/60 Hz
Touchscreen4.3 inch
Controlled valves1
Ambient temperature10–40 °C

Enquire about this product ↗

controller sk1 2 front

SK1-2

Touchscreen controller for two dispensing valves, shown for the supplied two-component system.

Sizes & technical details
ItemDetails
Dimensions as printed250(W) × 220(D) × 125(H)
Weight3.6 kg
Power supplyAC 110–250 V, 50/60 Hz
Touchscreen4.3 inch
Controlled valves2
Ambient temperature10–40 °C

Enquire about this product ↗

Equipment & integration

Control the dispense cycle.

From a time-pressure dispenser at the workbench to a valve controller inside an automated cell, we connect control to the application. Material delivery, operator use and machine interfaces are handled together, with practical support for setup and integration.

Manual and machine triggering

We configure triggering around the workstation, fixture or production equipment, so dispense commands fit naturally into the operating sequence.

Control matched to material delivery

Our selection covers the relationship between controller, barrel, cartridge, reservoir and valve. The result is a coordinated setup rather than a collection of separate components.

Straightforward production use

We support practical settings, recipe handling and machine status indications, with the level of control suited to the application and its operators.

System components

Connect the complete fluid path.

SET / San-Ei Tech SV51

Dispensing valves

Controlled delivery and clean shut-off at the part. We match the valve and fluid path to the material, then integrate the head, feed system, mounting and controls.

Free testing. Free solution advice.

Discuss your application with our engineers. We handle the technical evaluation with you.